www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com key features: ? 1w output power ? 5.7 kv isolation ? 15 kv/ s cmti ? 40 standard models ? miniature sip case ? -40c to +85c operation ? industry standard pin-out ? low cost mhi100di5.7 high isolation, 1w sip single & dual output dc/dc con vert ers input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 15 vdc input 13.5 15.0 16.5 24 vdc input 21.6 24.0 26.4 input filter capacitor filter output parameter conditions min. typ. max. units output voltage accuracy ?.0 % output voltage balance dual output, balanced loads ?.1 ?.0 % line regulation for v in change of 1% ?.2 % load regulation, see note 2 see model selection guide ripple & noise (20 mhz) see note 3 100 mv p - p temperature coef cient ?.01 ?.02 %/? output short circuit momentary (0.5 sec max) general parameter conditions min. typ. max. units isolation voltage rated for 60 sec 5,200 vdc tested for 1 sec 5,700 isolation resistance 500 vdc 10 g? isolation capacitance 100 khz, 1v 7 pf common mode transient immunity 15 kv/? switching frequency 100 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 ? case +100 storage temperature range -55 +125 ? cooling free air convection humidity rh, non-condensing 95 % physical case size see mechanical diagram (page 3) case material non-conductive black plastic (ul94-v0) weight 0.08 oz (2.4g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 2.0 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (0.1 sec) 5 vdc input 9.0 vdc 12 vdc input 18.0 15 vdc input 20.0 24 vdc input 30.0 lead temperature 1.5 mm from case for 10 sec 260 ? caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. electrical speci? cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. series
www.micropowerdirect.com micropower direct 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com model selection guide model number input output ef? ciency (%, typ) load regulation (%, max) capacitive load (f, max) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load mhi105s-03di5.7 5 4.5 - 5.5 286 35 3.3 303 0.0 70 ?0.0 1,000 500 mhi105s-05di5.7 5 4.5 - 5.5 286 35 5.0 200 0.0 70 ?5.0 470 500 mhi105s-09di5.7 5 4.5 - 5.5 266 35 9.0 111 0.0 75 ?0.0 470 500 mhi105s-12di5.7 5 4.5 - 5.5 261 35 12.0 84 0.0 77 ?0.0 220 500 mhi105s-15di5.7 5 4.5 - 5.5 254 35 15.0 66 0.0 78 ?0.0 220 500 mhi105d-05di5.7 5 4.5 - 5.5 282 35 ?.0 ?00 ?.0 71 ?5.0 220 500 mhi105d-09di5.7 5 4.5 - 5.5 269 35 ?.0 ?6 ?.0 75 ?0.0 220 500 mhi105d-12di5.7 5 4.5 - 5.5 262 35 ?2.0 ?2 ?.0 77 ?0.0 100 500 mhi105d-15di5.7 5 4.5 - 5.5 254 35 ?5.0 ?3 ?.0 78 ?0.0 100 500 mhi105d-1509di5.7 5 4.5 - 5.5 260 35 +15.0 +33 ?.0 76 ?0.0 100 500 -9.0 -55 220 500 mhi112s-03di5.7 12 10.8 - 13.2 117 17 3.3 303 0.0 71 ?0.0 1,000 250 mhi112s-05di5.7 12 10.8 - 13.2 117 17 5.0 200 0.0 71 ?5.0 470 250 mhi112s-09di5.7 12 10.8 - 13.2 110 17 9.0 111 0.0 76 ?0.0 470 250 mhi112s-12di5.7 12 10.8 - 13.2 108 17 12.0 84 0.0 78 ?0.0 220 250 mhi112s-15di5.7 12 10.8 - 13.2 104 17 15.0 66 0.0 79 ?0.0 220 250 mhi112d-05di5.7 12 10.8 - 13.2 116 17 ?.0 ?00 ?.0 72 ?5.0 220 250 mhi112d-09di5.7 12 10.8 - 13.2 111 17 ?.0 ?6 ?.0 75 ?0.0 220 250 mhi112d-12di5.7 12 10.8 - 13.2 108 17 ?2.0 ?2 ?.0 78 ?0.0 100 250 mhi112d-15di5.7 12 10.8 - 13.2 104 17 ?5.0 ?3 ?.0 79 ?0.0 100 250 mhi112d-1509di5.7 12 10.8 - 13.2 107 17 +15.0 +33 ?.0 77 ?0.0 100 250 -9.0 -55 220 250 mhi115s-03di5.7 15 13.5 - 16.5 95 16 3.3 303 0.0 70 ?0.0 1,000 200 mhi115s-05di5.7 15 13.5 - 16.5 95 16 5.0 200 0.0 70 ?5.0 470 200 mhi115s-09di5.7 15 13.5 - 16.5 89 16 9.0 111 0.0 75 ?0.0 470 200 mhi115s-12di5.7 15 13.5 - 16.5 90 16 12.0 84 0.0 75 ?0.0 220 200 mhi115s-15di5.7 15 13.5 - 16.5 84 16 15.0 66 0.0 79 ?0.0 220 200 mhi115d-05di5.7 15 13.5 - 16.5 94 16 ?.0 ?00 ?.0 71 ?5.0 220 200 mhi115d-09di5.7 15 13.5 - 16.5 90 16 ?.0 ?6 ?.0 75 ?0.0 220 200 mhi115d-12di5.7 15 13.5 - 16.5 86 16 ?2.0 ?2 ?.0 78 ?0.0 100 200 mhi115d-15di5.7 15 13.5 - 16.5 84 16 ?5.0 ?3 ?.0 79 ?0.0 100 200 mhi115d-1509di5.7 15 13.5 - 16.5 87 16 +15.0 +33 ?.0 76 ?0.0 100 200 -9.0 -55 220 200 mhi124s-03di5.7 24 21.6 - 26.4 60 12 3.3 303 0.0 70 ?0.0 1,000 150 mhi124s-05di5.7 24 21.6 - 26.4 60 12 5.0 200 0.0 70 ?5.0 470 150 mhi124s-09di5.7 24 21.6 - 26.4 56 12 9.0 111 0.0 75 ?0.0 470 150 mhi124s-12di5.7 24 21.6 - 26.4 53 12 12.0 84 0.0 78 ?0.0 220 150 mhi124s-15di5.7 24 21.6 - 26.4 52 12 15.0 66 0.0 80 ?0.0 220 150 mhi124d-05di5.7 24 21.6 - 26.4 59 12 ?.0 ?00 ?.0 71 ?5.0 220 150 mhi124d-09di5.7 24 21.6 - 26.4 56 12 ?.0 ?6 ?.0 75 ?0.0 220 150 mhi124d-12di5.7 24 21.6 - 26.4 55 12 ?2.0 ?2 ?.0 77 ?0.0 100 150 mhi124d-15di5.7 24 21.6 - 26.4 53 12 ?5.0 ?3 ?.0 78 ?0.0 100 150 mhi124d-1509di5.7 24 21.6 - 26.4 55 12 +15.0 +33 ?.0 75 ?0.0 100 150 -9.0 -55 220 150 notes: 1. the speci ed maximum capacitive load is for each output. 2. load regulation is measured over a range of 20% i out to 100% i out . 3. when measuring output ripple & noise, it is recommended that an external capacitor (1 f typ.) be placed from the +v out to the -v out pins for single output units and from each output to common for dual output models. 4. the converter should be connected to a low ac-impedance source. an input source with a highly inductive impedance may affect the stability of the converter. in applications where the converter output loading is high and input power is sup- plied over long lines, it may be necessary to use a capacitor on the input to insure start-up. in this case, it is recommended that a low esr (esr <1.0 at 100 khz) capacitor be mounted close to the converter. for 5v input units a 2.2 f is recom- mended; for 12v & 15v input units, a 1.0 f; and for 24v units a 0.47 f. 5. operation at no-load will not damage the unit, but they may not meet all speci ca- tions. 6. it is recommended that a fuse be used on the input of a power supply for protection. see the model selection tables for the correct rating. derating curve
www.micropowerdirect.com micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com notes: the mhi100x-xxd series is a good choice for igbt applications. they are designed to withstand the extra stress caused by the high voltage switching transients present in igbt drive circuits. the mhi1xxd-1509di5.7 models are speci - cally designed for use with ?62?type drivers. the igd962 (available from mpd ) is a hybrid integrated circuit speci cally designed to drive n-channel igbt modules. it provides the i/o isolation, high speed, drive voltage stability and fault protection required to control most mos gated power devices. the drawing at right illustrates a typical connec- tion of the mhi105d-1509di5.7 to the igd962 . for more information on this connection, please contact the factory. mechanical dimensions pin single output 1+v in 2-v in 5-v out 6 no pin 7+v out pin con nec tions notes: all dimensions are typical in inches (mm) tolerance x.xx = ?.02 (?.50) pin dual output 1+v in 2-v in 5-v out 6 common 7+v out igbt applications
|
